Description
ESP switch for CITROEN, PEUGEOT and other Stellantis models
Part description
This used Citroën Peugeot ESP switch, bearing part numbers 9817027877 and 98170278ZD, is a replacement part for repairing the electronic stability control system. It is suitable for replacing an original switch that is mechanically damaged or not working, provided the fault is actually in the switch itself.
The source information lists the Citroën Berlingo K9, FIAT DOBLO III, OPEL COMBO E K9, PEUGEOT RIFTER and Toyota ProAce City. When selecting a part, it is important to compare the product number, connector and mounting design with the original part; the model name alone may not be sufficient to ensure the correct selection. This used part provides an option for replacing a damaged switch without buying a new one.
Technical information
- Manufacturer: not specified; Stellantis / CITROEN / PEUGEOT are listed in the source information.
- Model: Citroën Berlingo K9; FIAT DOBLO III; OPEL COMBO E K9; PEUGEOT RIFTER; Toyota ProAce City.
- Part type: ESP switch, electrical control component.
- Condition: used part.
- Product numbers: 9817027877, 98170278ZD.
- Additional numbers: not specified.
- Model years, engine types and specific equipment versions: not specified.
Product codes
Product codes: 9817027877, 98170278ZD.
Both numbers are taken from the source information for this product. Before replacement, compare them with the number on the original switch and also check that its physical design matches.
Installation recommendations
The following procedure is a general guide for replacing an electrical switch of this type. The exact method of access, removal and connection depends on the specific model and vehicle version. Follow the manufacturer’s service procedure; the source information does not include specific installation instructions for this part.
1) Before installation
- Compare the part number, shape, dimensions, control surface, mounting and connector with the original part.
- Inspect the used switch: check for cracks, damaged clips, the condition of the contacts and any signs of moisture or corrosion.
- Check that the control moves without sticking. Do not use excessive force.
- Before replacement, distinguish a faulty switch from a wiring problem or a fault in the ESP system itself. An illuminated ESP warning light alone does not confirm a faulty switch.
2) Required tools and materials
- Plastic tools for carefully removing trim.
- Standard hand tools, depending on the fasteners used.
- A flashlight, a clean cloth and, if necessary, a product suitable for cleaning electrical contacts and compatible with the materials involved.
- If needed, a measuring instrument or diagnostic equipment to identify the cause of the fault.
3) Step-by-step installation procedure
- Park the vehicle safely, secure it against movement and switch off the ignition.
- Following the manufacturer’s procedure, allow the electrical systems to enter their rest state and disconnect the battery before working on the electrical connection.
- Refer to the service documentation for the specific vehicle to determine how to access the switch. Do not blindly pry at surrounding parts.
- If trim needs to be removed, release its fasteners with a suitable tool and protect visible surfaces from scratches.
- Before disconnecting the switch, note its orientation and the routing of the wiring, for example by taking a photograph.
- Release the switch from its mounting without excessively bending the clips or pulling on the wires.
- Unlock the connector and disconnect it by pulling on its housing, not on the wires.
- Check the connector and accessible wiring. Repair any damage or corrosion before connecting the replacement part.
- Compare the two switches again and connect the replacement. The connector must be fully seated and its lock must secure the connection properly without force.
- Fit the switch into its mounting, check that the wiring is routed freely and reinstall any trim that was removed.
- Reconnect the battery and restore the vehicle to operation according to the manufacturer’s procedure. Then check that it works.
4) Post-installation checks and function verification
- Check that the switch is firmly seated, the button operates correctly and the surrounding trim is securely mounted and undamaged.
- Under the conditions specified in the vehicle manual, test the system’s response to the switch and check the relevant indicator, if fitted to that version.
- If the switch does not respond or the ESP fault persists, proceed with diagnostics. Do not replace the part again without identifying the cause.
- Only carry out a test drive after the basic checks have been completed successfully, with the safety systems active. Do not test its function by deliberately inducing a skid; if the ESP fault has not been resolved, arrange for a professional assessment first.
5) Most common installation mistakes and how to avoid them
- Selecting based on appearance alone: also compare the product number, connector and mounting.
- Breaking the clips: first determine how they are secured and use suitable tools.
- Pulling on the wires: disconnect the connector only after unlocking it, and hold it by its housing.
- Connector not fully engaged or wiring pinched: check the connection and wire routing before closing the trim.
- Confusing a system fault with a faulty button: use appropriate diagnostics to verify the cause of the problem before replacement.
Reasons why the part may become damaged
The following are general causes of damage that may affect electrical switches of this type; they are not a description of defects identified in the part being offered:
- Mechanical wear of the operating mechanism and contacts through repeated use.
- Excessive pressure or impact, which may damage the button, switch housing or mounting.
- Ingress of liquid, moisture and dirt, which may cause sticking or corrosion of the contacts.
- Careless removal, which may break the clips or damage the connector.
- Damaged or loose electrical connection, which may cause intermittent operation or symptoms similar to a fault in the switch itself.





