Handbrake control Citroën DS Peugeot 9813146377 98131463ZD

€36.00

Stellantis CITROEN PEUGEOT
9813146377 98131463ZD

1 in stock

Description

Electronic parking brake switch for CITROEN, PEUGEOT and other Stellantis models

Part description

This used electronic parking brake switch is used to activate and release the brake. It is a suitable solution when replacing a damaged switch or one that responds unreliably. It is not the brake mechanism itself, but an electrical control component.

When looking for a replacement part, pay particular attention to the numbers 9813146377 and 98131463ZD. Before choosing, compare the numbers, connector, shape and mounting with the original switch. The model name alone may not be enough to select the correct version.

Technical information

  • Manufacturer: not specified; the source material lists the designation Stellantis CITROEN PEUGEOT.
  • Model: Citroën Berlingo K9; FIAT DOBLO III; OPEL COMBO E K9; PEUGEOT RIFTER; Toyota ProAce City.
  • Other numbers: not specified.
  • Part type: electronic parking brake switch.
  • Category: electrical components – other controls and switches – parking brake.
  • Condition: used part.

Product codes

  • Product codes: 9813146377, 98131463ZD.

Both designations are listed in the source material for this product. Comparing them with the designation on the original part is an important part of choosing a replacement.

Installation recommendations

The following procedure generally applies to this type of electrical switch. The exact method of access, removal and commissioning depends on the specific model and vehicle version. Follow the manufacturer’s service documentation; the switch is part of a safety-critical system.

1) Before installation

  • Check the body of the used switch, the control surface, fasteners and connector. Look for cracks, deformation, corroded contacts and signs of water ingress.
  • Compare the product numbers, shape, mounting and connector design with the old part.
  • Check whether the fault is actually related to the switch. A parking brake malfunction can also be caused by the power supply, wiring or another part of the system.
  • Secure the vehicle against movement independently of the electronic parking brake.

2) Tools and materials required

  • Standard hand tools suitable for the fasteners used.
  • Plastic trim removal tools if the trim needs to be released.
  • A flashlight, clean cloth and, if needed, a product suitable for cleaning electrical contacts.
  • Equipment to secure the vehicle against movement; suitable diagnostic equipment may also be needed, depending on the nature of the fault.

3) Step-by-step installation procedure

  1. Park the vehicle on a level, safe surface and secure it against unintended movement.
  2. Refer to the service documentation to find out the prescribed parking brake state for replacing the switch and how to safely shut down the electrical system.
  3. Switch off the ignition, follow the prescribed procedure for allowing the electronics to go to sleep and disconnecting the battery, as specified by the vehicle manufacturer.
  4. Carefully access the switch. If necessary, release covers and trim using suitable tools and without prying forcefully.
  5. Before disconnecting, note the wiring route and connector orientation, for example by taking a photo.
  6. Release the connector lock and disconnect the connector by holding its body. Do not pull on the wires.
  7. Release the fasteners and remove the original switch without damaging the surrounding area or brackets.
  8. Compare the two parts and check the mating connector. If the contacts or wiring are damaged, repair this fault first.
  9. Fit the replacement switch and secure it correctly. The part must seat properly without excessive force.
  10. Connect the connector until its lock engages and position the wiring so that it is not stretched or pinched.
  11. Refit the covers that were removed, restore the power supply according to the manufacturer’s procedure and carry out the prescribed function check.

4) Checks after installation and test drive / function check

  • With the vehicle stationary and secured, first check that the parking brake responds to the activation and release commands as described in the vehicle manual.
  • Check the brake status indicator and any warning messages. The mechanical response of the button alone does not confirm that the entire system is functioning correctly.
  • Check that the switch is securely seated and that the control moves freely.
  • Only carry out a short test drive after a successful static check and confirmation that the brake has been released correctly. Do not test the parking brake while driving.
  • If the response is unreliable or a fault message remains, do not use the vehicle until the cause has been resolved.

5) Common installation errors and how to avoid them

  • Choosing based only on the vehicle model: also compare the part designation, connector and mounting.
  • Replacing the part without identifying the cause of the fault: check the power supply, connections and condition of the wiring beforehand.
  • Damaging clips and the connector: release the locks first and do not use excessive force.
  • Pinched wires or a connector that is not fully engaged: check their routing and secure connection before closing the trim.
  • Relying on the parking brake during repairs: use an independent means of securing the vehicle against movement.

Reasons why the part may become damaged

Faults in this type of switch can generally occur for the following reasons; this is not a description of damage found on the item offered:

  • Mechanical wear of the control mechanism and contacts due to prolonged use.
  • Ingress of liquids and dirt, which may cause sticking, corrosion or unreliable switching.
  • Excessive force or impact, resulting in a broken control or mounting component.
  • Careless removal, which can damage the clips, connector or its contacts.
  • Moisture and poor electrical contact, which may cause intermittent responses. Similar symptoms can also be caused by a fault outside the switch itself.

Additional information

Weight 0.3 kg

Unless otherwise specified in the description, all photos are for illustrative purposes only.

We reserve the right to replace the ordered reference with the manufacturer's replacement reference.

The parts come from crashed vehicles, are carefully inspected, and we provide a 12-month warranty on functionality for them.