Citroën Peugeot control 9817735877 98177358ZD

€15.00

Stellantis CITROEN PEUGEOT
9817735877 98177358ZD

1 in stock

SKU: 9973-N34_K25 Categories: , ,

Description

Lane departure warning control for CITROEN, PEUGEOT and other Stellantis models

Part description

Used lane departure warning control with part numbers 9817735877 and 98177358ZD is designed to operate the vehicle’s corresponding driver assistance function. It is a control element, not the system’s sensor or camera itself. Replacing a non-functional or mechanically damaged control with a used part is a cost-effective alternative to buying a new one.

When selecting a part, compare the product numbers, control design, connector and mounting points with the existing part. Matching the model name alone is not sufficient, as the design may depend on the vehicle’s equipment.

Technical information

  • Manufacturer: not specified; the supplied information lists the designation Stellantis CITROEN PEUGEOT.
  • Model: Citroën Berlingo K9, FIAT DOBLO III, OPEL COMBO E K9, PEUGEOT RIFTER, Toyota ProAce City.
  • Other numbers: not specified.
  • Part type: lane departure warning control.
  • Category: electrical components – other controls and switches.
  • Condition: used part.

The models are taken from the supplied labels. Model years, engine types and exact equipment variants are not specified in the supplied information.

Product codes

  • Product codes: 9817735877, 98177358ZD.

Use both designations when searching for a replacement control and comparing it with the numbers on the original part.

Installation recommendations

The following general procedure applies to this type of electrical control. The exact method of access, removal and function testing depends on the specific model and vehicle configuration. The supplied information does not include a model-specific installation procedure.

1) Before installation

  • Compare the markings on the old and replacement parts, the shape of the front section, symbols, connector, contacts and mounting points.
  • Inspect the used control: check for cracks, damaged clips, bent contacts, corrosion and signs of liquid ingress.
  • Make sure the control moves without sticking. Smooth mechanical movement alone does not confirm electrical functionality.
  • Before replacing the part, rule out any visible damage to the connector or wiring. The control itself may not be the cause of the assistance system’s malfunction.

2) Required tools and materials

  • Plastic trim removal tools for carefully releasing trim panels.
  • Standard hand tools appropriate for the fasteners used.
  • A flashlight, soft protective mat and clean cloth.
  • If needed, a product suitable for cleaning electrical contacts; use it according to the manufacturer’s instructions and do not apply it inside the control without careful consideration.

3) Step-by-step installation procedure

  1. Park the vehicle safely, secure it against movement and switch off the ignition.
  2. Following the vehicle’s service procedure, allow the electrical systems to enter their standby state and disconnect the power as prescribed.
  3. Determine how the control is mounted and how to access it. Do not force off covers without first checking the position of the clips or screws.
  4. If access requires removing trim, carefully release it using suitable tools and protect visible surfaces from scratches.
  5. Release the original control’s fasteners and pull it out only far enough to access the connector. Do not strain the wiring.
  6. Release the connector lock and disconnect it by pulling on the connector body, not the wires.
  7. Inspect the connector and accessible wiring. If you find corrosion, overheating or damage, first address the cause of the fault.
  8. Compare the two controls again. If the connector, its keying or the mounting does not match, do not proceed by forcing or modifying the fit.
  9. Connect the replacement control and make sure the connector is properly secured. Route the wiring so that it is neither pinched nor stretched.
  10. Position the control, secure it using the original method and refit any covers that were removed. Restore power according to the vehicle manufacturer’s procedure.

4) Post-installation checks and function testing

  • Check that the control is firmly seated, the trim is properly fitted and the control moves freely.
  • After switching on the ignition, check that the control responds as described in the vehicle manual and that any relevant indicator appears.
  • If a test drive is required to verify the system, carry it out in safe conditions and in accordance with the manufacturer’s instructions. Do not deliberately cause the vehicle to leave its lane in an unsafe manner.
  • If the fault persists, continue by diagnosing the power supply, wiring and relevant system; do not automatically assume that the control is faulty.

5) Common installation mistakes and how to avoid them

  • Selecting by appearance alone: always compare the part markings, connector and mounting points as well.
  • Breaking the clips: first determine how they are released and use appropriate force.
  • Pulling on the wires: disconnect the connector only after releasing its lock, and hold it by the body.
  • Connector not fully latched or wiring harness pinched: check that the connector is secured and the wiring is routed correctly before closing the trim.
  • Working on a powered circuit: follow the manufacturer’s procedure for safely disconnecting and reconnecting the power supply.

Reasons why the part may be damaged

The following are general possible causes of damage to this type of control; they do not describe faults in the item being offered:

  • Mechanical wear of the control mechanism over prolonged use.
  • Excessive force or impact, which can damage the button, control housing or its mounting.
  • Ingress of liquids and dirt, which can cause sticking or damage the electrical contacts.
  • Moisture and connector corrosion, which can cause an unreliable electrical connection.
  • Careless removal, especially prying with the wrong tool, breaking clips and pulling on the wiring.

Additional information

Weight 0.5 kg

Unless otherwise specified in the description, all photos are for illustrative purposes only.

We reserve the right to replace the ordered reference with the manufacturer's replacement reference.

The parts come from crashed vehicles, are carefully inspected, and we provide a 12-month warranty on functionality for them.