ECU Bosch EDC16C3 1.4 HDi 0281011089 9653202580

€48.00

Stellantis Citroën Peugeot
0281011089 9653202580 9647785580
1940WV 1940WW 1940FP 1942G5 1942G6

1 in stock

SKU: 4693-M18_K16 Categories: , ,

Description

BOSCH Control Unit for Peugeot 206 1.4 HDi

This Bosch EDC16C3 engine control unit (ECU) is designed for the Peugeot 206 1.4 HDi and carries common OEM references used in service and parts searches. Ideal for professional workshops and experienced DIY mechanics, this ECU manages fuel injection, common-rail pressure control, air/fuel mixture and emission-related functions to keep the HDi diesel running efficiently. Listing the familiar part numbers in the description helps technicians locate the correct unit quickly during diagnosis or replacement.

Technical Information

  • Manufacturer: Bosch
  • Model: Peugeot 206 1.4 HDi (ECU Type EDC16C3)
  • Product Codes: 0281011089, 9653202580, 9647785580
  • Other Numbers: 1940WV, 1940WW, 1940FP, 1942G5, 1942G6

Features And Benefits

Bosch EDC16C3 is a widely used engine management unit for early PSA 1.4 HDi engines. It provides precise injection timing and quantity control for improved fuel economy and reduced emissions. Replacing a faulty ECU with the correct reference restores drivability, idle stability and fault-code transparency for accurate diagnostics.

How The Unit Is Replaced

  1. Disconnect the vehicle battery before any work to avoid short circuits and damage to electronic components.
  2. Locate and remove the ECU — typically found in the engine bay or behind a protective cover depending on the vehicle configuration.
  3. Unplug all electrical connectors and mounting screws. Take care with locking tabs and connector latches.
  4. Install the replacement unit, reconnect all harnesses and secure the mounting points per manufacturer torque/fitment guidance.
  5. Perform required coding or cloning (see Installation and Coding – Important section) before test-running the engine.

Installation Recommendations

  • Always disconnect the battery before removing or fitting the ECU.
  • Protect the unit from moisture and contamination during installation; ensure sealing surfaces and connectors are clean and dry.
  • Observe ESD precautions: avoid touching pins and electronic components directly; use grounded tools or wrist strap if available.
  • Follow manufacturer removal/installation procedures and torque values where specified.

Installation and Coding – Important

  • The Unit Is Used And Is “Paired” With The Original Vehicle (VIN/PIN/Keys).
  • Options To Put The Unit Into Service:
    1. Cloning Data From The Old Unit (EEPROM/Flash) – After Cloning The Unit Is Plug And Play.
    2. Virginization And Subsequent Initialization/Telecoding Via DiagBox (Or Online) + Key Adaptation.
  • Recommended To Be Performed By A Specialist With PSA Service Equipment (DiagBox/Lexia/PP2000).
  • Always Disconnect The Battery Before Removal/Installation And Follow The Manufacturer Procedure To Avoid Damaging The Unit.

Why This Part Fails Most Often

ECUs for the 1.4 HDi commonly fail due to water ingress or corrosion (especially in vehicles with engine-bay mounting), thermal stress and solder joint fatigue on the PCB, voltage spikes from charging systems or jump-starting, and connector/wiring harness faults that create intermittent errors. Symptoms include engine stalling, loss of injector control, persistent fault codes, limp-home mode and failure to start.

Practical Tips For Diagnosis

  • Check power supply and ground continuity before condemning the ECU.
  • Inspect connectors and wiring for corrosion, bent pins or rodent damage.
  • Read freeze-frame data and stored fault codes with a capable scanner to confirm ECU-origin faults vs. sensor/actuator failures.
  • Consider cloning or reading EEPROM contents before replacement to preserve vehicle adaptations and immobilizer-related data.

Compatibility Notes

This listing references the most common OEM codes for the Bosch EDC16C3 used on Peugeot 206 1.4 HDi applications. Use the product codes listed in Technical Information to verify fitment in parts catalogs or during component selection.

Additional information

Weight 1 kg

Unless otherwise specified in the description, all photos are for illustrative purposes only.

We reserve the right to replace the ordered reference with the manufacturer's replacement reference.

The parts come from crashed vehicles, are carefully inspected, and we provide a 12-month warranty on functionality for them.