Speedometer, 168,000 km, instrument cluster, Citroën C4 96572391ZD

€61.00

Stellantis CITROEN PEUGEOT
P96572391ZD 6106VZ 6106WA

1 in stock

SKU: 9956-E3_K27 Categories: , ,

Description

Complete instrument cluster for CITROEN C4 vehicles up to 2008
From a vehicle with 168000 km on the odometer

Part description

Used instrument cluster for Citroën C4 I, commonly referred to as a speedometer or gauges. It displays operating data and warnings to the driver. When replacing a faulty cluster, it is important to compare not only its appearance, but also the product number and connector design.

The part is listed in the documentation under number 96572391ZD; the following designations are also given: P96572391ZD, 6106VZ and 6106WA. It comes from a vehicle with 168000 km on the odometer; this figure describes the source vehicle and is not a guaranteed odometer reading after installation in another vehicle. For a repair, this used part offers an option for retaining the corresponding instrument cluster design without buying a new unit.

Technical information

  • Manufacturer: not specified; the documentation lists the designation Stellantis CITROEN PEUGEOT.
  • Model: Citroën C4.
  • Generation: C4 I.
  • Fitment according to the documentation: CITROEN C4 vehicles up to 2008.
  • Part type: complete instrument cluster / speedometer.
  • Condition: used part.
  • Source vehicle mileage: 168000 km.
  • Additional numbers: P96572391ZD, 6106VZ, 6106WA.

Product codes

  • Product codes: 96572391ZD, P96572391ZD, 6106VZ, 6106WA.
  • Model: Citroën C4.

When selecting a part, compare the numbers listed above with the markings on the original cluster. Matching the model and appearance alone does not necessarily mean that the electrical design or configuration is the same.

Installation recommendations

The following procedure generally applies to this type of electrical part. The exact removal procedure, battery disconnection rules, and any required configuration depend on the specific model and vehicle version. The documentation does not state whether this unit requires diagnostic-tool adaptation.

1) Before installation

  • Compare the product numbers, connectors, connector keying, mounting points, and display design with the old unit.
  • Check the housing, mounting points, and contacts. Look for cracks, signs of moisture, corrosion, or damaged pins.
  • First rule out a power supply, fuse, or wiring fault that could mimic an instrument cluster failure.
  • Record the original odometer reading and the symptoms of the fault. Before connecting a used cluster, check the service documentation for the rules on storing and synchronizing mileage. On some systems, connecting a different cluster may change the stored reading; therefore, do not connect it just to test it without understanding how this works.

2) Tools and materials required

You will generally need suitable screwdrivers or bits for the fasteners used, a plastic trim removal tool, a flashlight, and materials to protect surrounding surfaces. A multimeter and diagnostic equipment suitable for the vehicle may be required to check an electrical fault or perform any necessary configuration.

3) Step-by-step installation procedure

  1. Park the vehicle safely, secure it against movement, and record the available information from the original cluster.
  2. Verify that the replacement part is compatible and clarify any configuration requirements and procedures for handling the mileage reading.
  3. Switch off the ignition and electrical consumers. Allow the electronic systems to enter sleep mode according to the manufacturer’s instructions.
  4. Disconnect the battery as specified for the particular vehicle.
  5. Carefully remove the trim needed to access the cluster. Do not force the plastic clips, and protect removed parts from scratches.
  6. Release the original cluster’s fasteners and support it so that its weight does not strain the wiring.
  7. Unlock the connectors and disconnect them by gripping their housings, not by pulling on the wires.
  8. Check the condition of the connectors and wiring. Resolve any damage or source of moisture found before installing the replacement part.
  9. Connect the replacement cluster, secure the connectors properly, and position it without pinching the wiring. Tighten the fasteners according to the service procedure without overstressing the plastic mounting points.
  10. Reconnect the battery and bring the electronics back into operation according to the manufacturer’s instructions. If the specific version requires configuration, perform it using suitable diagnostic equipment.
  11. Check the basic functions and then complete the trim installation. Record the part replacement and the odometer reading after installation.

4) Post-installation checks and function verification

Check display legibility, backlighting, and the operation of available gauges and warning lights, depending on the vehicle’s equipment. Check that the display does not cut out or flicker. If the basic check reveals no faults and the vehicle is roadworthy, take a short, safe test drive and verify that the speed is displayed. Diagnose any error messages first; do not clear them without identifying the cause.

5) Most common installation mistakes and how to avoid them

  • Choosing a part based on appearance alone: also compare the markings, connectors, and configuration requirements.
  • Connecting without checking how mileage is handled: review the service procedures for the specific version in advance and keep a record of the replacement.
  • Working while the power is connected: follow the procedure for switching off the electronics and disconnecting the battery.
  • Connector locks not fully secured or wires pinched: check that the connectors are locked in place and the wiring is routed freely before refitting the trim.
  • Forcing the mounting points and trim: first locate and release all retaining clips.

Reasons why the part may become damaged

Instrument cluster faults may generally arise from the following causes; this is not a description of any faults found in the item offered:

  • Aging electronics and connections due to prolonged use and temperature changes.
  • Moisture and corrosion, which can damage contacts and electronic circuits.
  • Power supply fluctuations or incorrect electrical work, for example, due to improper handling of the electrical system.
  • Vibration and loose connections, which can cause intermittent display of information.
  • Mechanical damage during removal, especially broken mounting points, damaged connectors, or a damaged housing.

Additional information

Weight 1.9 kg

Unless otherwise specified in the description, all photos are for illustrative purposes only.

We reserve the right to replace the ordered reference with the manufacturer's replacement reference.

The parts come from crashed vehicles, are carefully inspected, and we provide a 12-month warranty on functionality for them.