Right front window mechanism Peugeot 3008 5008 9682808880 9222FF

Description

Electric window starter for PEUGEOT 3008 and 5008 cars of the first generation
Front passenger door

Part description

This used right front window mechanism is intended for Peugeot 3008 I and Peugeot 5008 I cars. It is an electric window opener for the passenger front door, which ensures smooth lowering and raising of the side glass. Parts of this type are often searched by serial number, so it is important to keep an eye out for 9682808880 and 9222FF.

The mechanism is suitable as a replacement for a non-functional, worn or damaged original part. For auto mechanics and DIYers, the possibility to keep the original solution designed for the given type of car is an advantage.

Technical information

• Manufacturer: Stellantis Citroën Peugeot
• Model: Peugeot 3008 I, Peugeot 5008 I
• Other numbers: 9682808880, 9222FF

Product codes

• Product codes: 9682808880, 9222FF
• Models: PEUGEOT 3008 I, PEUGEOT 5008 I

Installation recommendations

Typically for this type of part, the exact replacement procedure may vary depending on the specific door design and vehicle equipment. Below is a general and safe procedure for replacing the front door power window mechanism.

1) Before assembly

• Check that the side of the part and the design of the connectors match the original piece.
• Compare product numbers 9682808880 and 9222FF with the old part.
• Inspect guide parts, mounts and electrical connections for damage.
• Verify that the mechanism is not mechanically crossed, corroded or excessively worn.

2) Necessary tools and materials

• set of common hand tools
• screwdrivers and bits for panel removal
• plastic levers for removing the tapestry
• Ratchet with matching attachments
• detergent for removing dirt
• protective gloves and possibly tape to secure the glass

3) Step-by-step assembly procedure

1. Disconnect the battery and secure the vehicle against unwanted movement.
2. Dismantle the inner lining of the door so as not to damage the handles and covers.
3. Disconnect the electrical connectors related to the door equipment.
4. Carefully access the space of the window download mechanism.
5. Secure the glass in the up position or in a safe service position to prevent it from falling during disassembly.
6. Disconnect or release the glass from the original mechanism according to the design of the particular design.
7. Remove the old mechanism including its mounting and compare it with the new piece.
8. Install the used mechanism in its original place and make sure that all fixing points are correctly seated.
9. Connect the electrical connector and connect the mechanism to the glass.
10. Before fully assembling the door, check manually and electrically whether the part moves freely and without binding.
11. Put back the guards, inner door trim and all removed parts.
12. When finished, reconnect the battery.
• 4) Post-assembly checks and test drive/function verification
  • Try repeatedly pulling and pulling the window to its full extent.
  • Watch if the glass moves smoothly, without warping or unusual noises.
  • Check that the glass is properly seated after closing.
  • After installation, check that there is no excessive noise from the door or clearance in the mounting when driving.

  5) The most common assembly mistakes + how to avoid them

  • Swapping right and left side – always compare the original part before assembly.
  • Door panel damage – use suitable plastic levers and do not use force.
  • Incorrect seating of the glass – check the operation of the mechanism several times before final assembly.
  • Assembly without checking connectors and fixings – check all connections and fixing points before closing the door.
  • Starting the mechanism with unsecured glass – the glass must always be securely fixed during work.

  Reasons why the part is damaged

  • normal mechanical wear and tear during long-term use
  • increased stress when frequently pulling in and out of the window
  • stiffening of the window guide and subsequent overloading of the mechanism
  • intrusion of moisture and dirt into the door area
  • damage to wiring or electrical controls
  • forced closing or operation with the glass stuck