Bosch ME7.4.5 Engine Control Unit (ECU) 0261208491 9657489380 1940SV

€48.00

Stellantis Citroën Peugeot
0261208491 9657489380 1940SV 9652552380 NFP

1 in stock

SKU: 9961-S7_K16 Categories: , ,

Description

Engine Control Unit BOSCH ME7.4.5 For Citroën C4 1.6 16V

Overview

Bosch ME7.4.5 Engine Control Unit (ECU) designed for petrol 1.6 16V engines used in Citroën C4 and compatible Stellantis applications. This control unit manages fuel injection, ignition timing, idle control and emission-related functions to ensure optimal engine performance and drivability. Frequently referenced by its product codes, the ECU is a direct replacement option when the original unit fails or exhibits fault symptoms.

Fitment And Application

Primary Fitment: Citroën C4 1.6 16V (Bosch ME7.4.5 controlled petrol engines). May be fitted to other Stellantis vehicles that use the same Bosch ME7.4.5 calibration and matching product codes. Check the unit’s part numbers against the vehicle’s original ECU to confirm compatibility.

Technical Information

  • Manufacturer: Bosch
  • Model: ME7.4.5
  • Product Codes: 0261208491, 9657489380, 1940SV
  • Other Numbers: 9652552380, NFP

Function And Common Failures

Function: The ECU controls injection timing and duration, ignition advance, idle control, emission control strategies and communicates with other vehicle modules (engine sensors, throttle, immobilizer). It stores calibration and adaptation data in internal memory (EEPROM/Flash).

Common Failures: Typical causes of ECU malfunction include water ingress or condensation, corrosion on connectors, thermal stress and cracked solder joints, electrical surges or poor battery connections, and memory corruption (EEPROM/Flash). Symptoms of a failing ECU include no-start condition, intermittent stalling, limp-home mode, misfires, erratic idle or persistent engine fault codes.

Replacement Procedure

Basic Steps For Swap:

  1. Disconnect The Battery Before Any Work To Avoid Short Circuits And Voltage Spikes.
  2. Remove Interior/Engine Covers As Required To Access The ECU Location.
  3. Unplug Wiring Harness Connectors Carefully, Release Any Locking Tabs.
  4. Unbolt The ECU From Its Bracket And Remove From Vehicle.
  5. Fit The Replacement Unit Securely, Reconnect Harnesses And Reinstall Covers.
  6. Perform Required Coding/Cloning Or Initialization (See Installation And Coding Section).

Installation And Coding – Important

  • The Unit Is Used And Is “Paired” With The Original Vehicle (VIN/PIN/Keys).
  • Options To Commission:
  1. Cloning Data From The Old Unit (EEPROM/Flash) – After Cloning The Unit Is Plug And Play.
  2. Virginization And Subsequent Initialization/Telecoding Via DiagBox (Or Online) + Key Adaptation.
  • Recommended To Be Performed By A Specialist With PSA Service Equipment (DiagBox/Lexia/PP2000).
  • Always Disconnect The Battery Before Removal/Installation And Follow The Manufacturer’s Procedure To Avoid Damaging The Unit.

Mounting Recommendations

  • Ensure Connector Pins Are Clean And Dry; Do Not Force Connectors Into Place.
  • Inspect Wiring Loom For Damage, Repair Any Corroded Contacts Or Frayed Wires Before Reuse.
  • Protect The Unit From Moisture And Excessive Heat; Replace Seals Or Gaskets If Present.
  • If Cloning, Use Reliable EEPROM/Flash Equipment And Retain A Backup Of The Original Data Where Possible.
  • After Installation, Clear Fault Codes And Verify Sensor Readings And Engine Operation Under Load.

Why This Part Fails Most Often

The Most Common Reasons For Failure Are Environmental And Electrical Stress: Moisture Ingress Leading To Corrosion, Repeated Thermal Cycling Causing Solder Joint Fatigue, And Voltage Spikes From Poor Battery Connections Or Jump-Starting. Memory Corruption (EEPROM/Flash) Can Also Cause Intermittent Faults Or Total Loss Of Functionality.

Notes For Mechanics And DIY Enthusiasts

When replacing an ECU on a Citroën C4 1.6 16V, prioritize cloning or proper initialization to preserve immobilizer and engine-specific calibrations. If unsure about coding or key adaptation, have the final commissioning performed with PSA diagnostic tools to ensure full functionality and avoid drivability issues.

Additional information

Weight 0.9 kg

Unless otherwise specified in the description, all photos are for illustrative purposes only.

We reserve the right to replace the ordered reference with the manufacturer's replacement reference.

The parts come from crashed vehicles, are carefully inspected, and we provide a 12-month warranty on functionality for them.