Description
Windshield heating switch for CITROËN, PEUGEOT and other Stellantis models
Part description
This used windshield heating switch, bearing the numbers 9817027377 and 98170273ZD, is used to control this function in the vehicle. It is a suitable choice when replacing a damaged or non-functional switch, provided it matches the original version. Keeping the heating controls functional makes the vehicle easier to use in icy conditions and when visibility through the windshield is reduced.
When selecting a replacement, compare the product number, connector, mounting points and control surface design with the old part. Matching the vehicle model alone is not enough — the equipment version is also important. If the heating is not working, we recommend determining whether the fault is in the switch, power supply, wiring or the heating element itself before replacing the switch.
Technical information
- Manufacturer: not specified
- Model: Citroën Berlingo K9, FIAT DOBLO III, OPEL COMBO E K9, PEUGEOT RIFTER, Toyota ProAce City
- Part type: windshield heating switch
- Category: Electrical components / Other / Other controls and switches
- Condition: used part
- Additional numbers: not specified
The models are taken from the product labels provided. The information does not specify model years or individual equipment variants.
Product codes
- Product codes: 9817027377, 98170273ZD
Both numbers can be used when searching for a replacement Citroën Peugeot switch. Before installation, compare the numbers and physical design with the original part.
Installation recommendations
The following general procedure applies to this type of electrical switch. The exact access to the part, method for releasing the trim panels and procedure for disconnecting the power supply depend on the specific vehicle model and version. Follow the manufacturer’s service documentation.
1) Before installation
- Compare the numbers on both parts, body shape, control surface, mounting points and connector design.
- Inspect the used switch: check for cracks, damaged clips, the condition of the contacts and signs of moisture or overheating.
- Check that the control moves freely without sticking. Do not use force.
- Before replacement, check whether the cause of the heating failure is actually related to the switch.
2) Tools and materials required
- Plastic tools for careful trim removal.
- Standard hand tools suitable for the fasteners used.
- A flashlight, clean cloth and, if needed, a product suitable for electrical contacts.
- Measuring or diagnostic equipment for checking the electrical circuit, as required.
3) Step-by-step installation procedure
- Secure the vehicle against movement, switch off the ignition and turn off electrical accessories.
- Following the manufacturer’s instructions, allow the electronics to enter sleep mode and safely disconnect the power supply before working on the electrical part.
- Inspect how the surrounding panels are mounted. Locate the fasteners before releasing the panels to avoid damaging the trim.
- Carefully remove only the parts required to access the switch. Release the plastic clips using a suitable tool and without applying excessive force.
- Release the original switch from its mount and note its orientation and the routing of the wiring.
- Release the connector lock and disconnect it by holding the connector body, not by pulling on the wires.
- Inspect the connector and accessible wiring. Address any corrosion, loose contacts or signs of heat damage before connecting the replacement part.
- Compare the two switches again, especially the connector, its orientation and the mounting points. Do not force a part that does not match.
- Connect the connector to the replacement switch and check that the locking tab is properly engaged.
- Fit the switch and reinstall the removed parts. The wiring must not be pinched or under tension.
- Restore the power supply according to the manufacturer’s procedure and check operation.
4) Post-installation checks and function verification
- Check that the switch is securely fitted and that the control moves freely.
- Test switching the heating on and off under the operating conditions specified by the vehicle manufacturer. If there is an indicator, also check that it responds.
- Verify that the heating itself works, not just that the switch or indicator responds.
- If the fault persists, continue diagnosing the related circuit. Repeatedly replacing the switch without identifying the cause may not resolve the problem.
- A test drive is not usually required to verify the switch itself. If you do drive the vehicle, set off only when visibility is sufficient and test the controls safely while stationary.
5) Common installation mistakes and how to avoid them
- Selecting based on appearance alone: also compare the product number, connector and mounting points.
- Breaking the clips: first determine how to release them and use plastic trim removal tools.
- Pulling on the wires: disconnect the connector only after releasing the lock, and hold it by the body.
- Connector not fully engaged or wiring pinched: check that the connector is locked and the wires are routed correctly before closing the trim.
- Overlooking another fault: check the power supply and related electrical circuit before replacing the switch.
Reasons why the part may become damaged
The following factors can generally cause damage to this type of switch. They do not describe any faults identified in the item being offered.
- Mechanical wear of the control mechanism and contacts due to prolonged use.
- Ingress of moisture or dirt, which can cause contact corrosion or make the control stick.
- Excessive force during operation or removal, which can cause the body or mounting clips to break.
- Damaged or loose electrical connection, which can cause intermittent operation and localized contact heating.
- Improper cleaning, particularly allowing liquid to enter the electrical part of the switch.








