Description
Complete engine wiring harness for CITROËN and PEUGEOT vehicles with a 1.6 16V NFU engine
From a 2006 CITROËN C4
Part description
Used Citroën Peugeot 1.6 16V NFU engine wiring harness connects the engine components electrically and transmits power and signals between them. It is a suitable solution when replacing damaged wiring, where repairing individual wires and connectors is no longer worthwhile.
The part comes from a 2006 Citroën C4. The documentation lists the Citroën C4 and Peugeot 307 models and the part numbers 9657134480 and 656940, which make the harness easy to find. Before selecting it, compare the part numbers, connector design and individual branches with the original harness; matching the engine displacement alone is not sufficient.
Technical information
- Manufacturer: not specified; the documentation lists the designation Stellantis CITROEN PEUGEOT.
- Model: Citroën C4, Peugeot 307.
- Engine: 1.6 16V NFU.
- Part type: complete engine wiring harness.
- Condition: used part.
- Part origin: Citroën C4, year 2006.
- Other numbers: not specified; additional designation in the documentation: NFP.
Product codes
- Product codes: 9657134480, 656940.
- Additional designation: NFP.
- Models listed in the documentation: Citroën C4, Peugeot 307.
When looking for a replacement harness, use the numbers 9657134480 and 656940 in particular. The information that the part came from a 2006 vehicle does not define compatibility with all vehicles from that year.
Installation recommendations
The following procedure applies generally to engine wiring harnesses. The exact extent of disassembly, wiring routing and method for disconnecting and reconnecting the battery depend on the specific model and vehicle configuration. Follow the manufacturer’s service procedure.
1) Before installation
- Compare the markings on the replacement and original harnesses, the number and shape of the connectors, their mechanical keying, contact pinout, branch lengths and mounting points.
- Inspect the insulation, protective sleeves, grommets and clips. Check that no wires are chafed, broken or heat-damaged.
- Check the connector contacts and locking tabs. Address any corrosion, pushed-back contacts or cracked connector housing before installation.
- Determine the cause of the damage to the original wiring so that the same fault does not recur with the replacement part.
2) Tools and materials required
- Standard hand tools suitable for the fasteners and access in the vehicle.
- A suitable tool for releasing connector locks and cable clips.
- Labels or marking tape and a camera to record the harness routing.
- Electrical contact cleaner and, if necessary, suitable fastening and protective materials for automotive wiring.
- A multimeter and diagnostic equipment as required; perform measurements according to the wiring diagram and service procedure.
3) Step-by-step installation procedure
- Secure the vehicle against movement, switch off the ignition and allow the engine to cool.
- Follow the prescribed procedure for allowing the electronics to go to sleep and disconnect the battery according to the vehicle manufacturer’s instructions.
- Take photos of the original harness routing, its mounting points and the connections of its individual branches. Label similar connectors.
- Remove only the components that prevent safe access to the wiring, in accordance with the service procedure.
- Release the connector locks one by one and disconnect them by holding their housings. Do not pull on the wires or pry at the contacts.
- Release the clips, grommets and any bolted connections securing the harness. Remove the original wiring without forcing it.
- Lay the two harnesses side by side and compare the connectors, branching, lengths and mounting points again. If anything does not match, do not proceed with installation.
- Inspect the mating connector halves and the wiring routing locations. Remove any dirt and address the cause of any chafing or contamination of the harness.
- Route the replacement harness along the original path and according to the service documentation. Secure it so that it is not stretched, pinched or in contact with hot or moving parts.
- Connect the corresponding connectors and check that their locks engage. Restore any bolted connections according to the manufacturer’s specifications.
- Recheck all branches, clips and grommets, reinstall the removed components and reconnect the battery using the prescribed procedure.
- Check the system with the ignition switched on, then verify engine operation. If you notice the smell of overheating insulation, smoke or unusual behavior, stop the test immediately.
4) Post-installation checks and function verification
- Verify that the engine starts and runs steadily, and check the functions of components connected through the replaced harness.
- If necessary, use diagnostic equipment to check for stored faults and related operating data. Clearing fault codes alone does not resolve their cause.
- If the static check reveals no faults, take a short test drive. Then, with the engine switched off and cooled down, inspect the harness mounting and routing again.
5) Common installation mistakes and how to avoid them
- Mixing up similar connectors: label them before removal and refer to the documentation when reconnecting them; do not rely solely on their position.
- Connector locks not fully engaged: always check that the connectors are fully inserted and locked, without using excessive force.
- Stretched branches or cable ties that are too tight: leave enough slack to allow for engine movement and do not compress the insulation.
- Omitting clips and protective coverings: restore the specified mounting points so that the harness does not chafe or overheat.
- Replacing the harness without addressing the original cause: before putting the vehicle back into service, resolve issues such as fluid leaks, a damaged mating connector or an electrical fault in a connected component.
Reasons why the part gets damaged
Engine wiring harnesses are generally exposed to heat, vibration and dirt. Common causes of damage include:
- Insulation aging due to heat, which can cause the wire protection to become brittle and crack.
- Vibration and mechanical chafing when clips are missing or the harness is routed incorrectly.
- Ingress of moisture and operating fluids, which can damage the insulation, seals and electrical contacts.
- Improper repairs and work, such as unsuitable splices, pulling on wires or damaging connector locks.
- A short circuit or excessive electrical load, which can cause wires and contacts to overheat.
- Damage caused by rodents or during previous repairs, particularly chewed, pinched or cut wiring.
These are general causes of damage to this type of part, not a description of faults with the item being offered.








