Description
Bulb holder with bulbs for the right or left rear lamp for Peugeot 307 Estate (Kombi/SW) up to 2005. Bulb functionality is not guaranteed. Supplied with a piece of wiring.
This replacement tail lamp socket is designed for Peugeot 307 SW/Estate models and is ideal for mechanics and DIY enthusiasts looking for a direct-fit rear light solution. The part includes the bulb holders and a short length of pigtail wiring, making it suitable for restoring electrical contact in the rear lamp cluster. Common search terms: “Peugeot 307 SW bulb socket”, “rear lamp holder 6350Q6”, “tail light connector 6351Q6” — useful when searching by product code.
Technical Information
- Manufacturer: Stellantis (Citroën/Peugeot)
- Model: Peugeot 307 SW / Estate (Kombi) – Up To 2005
- Product Codes: 6350Q6, 6351Q6
- Additional Numbers: 89026938, 89026198
Function And Fitment
The Part Serves As The Electrical Socket For Rear Bulbs, Providing Mechanical Support And Electrical Contact For Brake Light, Tail Light, Indicator And (Where Applicable) Reverse Or Fog Bulbs Depending On The Lamp Assembly. It Fits Either The Left Or Right Rear Lamp On Peugeot 307 Estate (Kombi/SW) Models Produced Up To 2005.
Replacement Procedure
- Prepare: Park On A Level Surface And Ensure Ignition Is Off.
- Access Lamp: Open The Tailgate And Remove Interior Trim To Reach The Rear Lamp Cluster.
- Remove Lamp Assembly: Unscrew The Fasteners Holding The Lamp Cluster And Carefully Pull The Cluster Outwards.
- Disconnect Old Socket: Unplug The Factory Harness And Twist Out The Old Bulb Holder From The Lamp Housing.
- Install New Socket: Insert The New Holder Into The Lamp Housing, Secure It With The Same Retaining Clips Or Screws, And Connect The Supplied Wiring To The Vehicle Harness (Match Colors/Terminals).
- Test: Reconnect Power And Verify All Rear Light Functions (Brake, Tail, Indicator, Reverse/Fog As Applicable). Replace Any Non-Working Bulbs If Needed.
- Reassemble: Refit The Lamp Cluster And Interior Trim, Ensure All Fasteners Are Secure.
Installation Recommendations
- Use Proper Tools And Take Care When Removing Trim To Avoid Damage To Clips Or Wiring.
- Check Contact Surfaces For Corrosion Or Melting; Clean Contacts If Necessary Before Installation.
- Use Dielectric Grease On Contacts To Reduce Corrosion And Improve Long-Term Reliability.
- If The Pigtail Wiring Requires Splicing, Use Quality Connectors And Heat-Shrink Insulation For A Durable Repair.
Common Failure Reasons
Bulb Holders And Rear Lamp Sockets Typically Fail Due To Corrosion From Moisture Ingress, Salt Exposure, Heat Damage From Overheating Bulbs, Mechanical Wear From Vibration Or Impact, And Poor Electrical Contact Caused By Oxidation. Loose Or Broken Terminals And Melted Plastic Around Bulb Seats Are Also Frequent Causes Of Intermittent Or Complete Light Failure.
Durability And Maintenance
Lifespan Depends On Environmental Conditions; In Coastal Or Winter Salt Regions, Corrosion Can Appear Within Several Years, While In Drier Conditions The Socket May Last Significantly Longer. Regular Inspection During Service Intervals, Cleaning Contacts, And Replacing Aged Bulbs With Correct Wattage Helps Extend Service Life.
What Is Supplied
- Bulb Holder With Bulbs (Bulb Functionality Not Guaranteed)
- Short Length Of Wiring (Pigtail)
Why Choose This Part
Replacement Is A Cost-Effective Way To Restore Rear Light Functionality Without Replacing The Entire Lamp Assembly. The Part Is Searched Frequently By Product Codes 6350Q6 / 6351Q6, Making It Easy To Find When Ordering Or Comparing Fitment.
