Description
Right rear lamp for PEUGEOT 206 3/5-door vehicles. For production up to 6/2003. Passenger side.
This right rear tail lamp is a direct-fit replacement for Peugeot 206 (3-door and 5-door) models manufactured up to June 2003. Designed for professional workshops and experienced DIYers, the unit restores rear lighting functions and road-legal visibility after damage or wear. The complete assembly offers straightforward installation without bodywork modifications and ensures correct alignment with factory mounting points for a secure fit and reliable sealing against the elements.
Technical Information
- Manufacturer: Stellantis (Peugeot)
- Model: Peugeot 206 (3 & 5 Door) – Up To 06/2003
- Product Codes: 6351P1
- Other Numbers: NFP
Compatibility And Application
Fits Right (Passenger) Rear Position On Peugeot 206 Hatchbacks With 3 Or 5 Doors, Produced Until June 2003. Check Body Configuration And Mounting Points To Confirm Fitment Before Installation.
Function And Description
Rear Combination Lamp Assembly Serving As Tail/Position Light, Brake Light And Turn Signal (Function Dependent On Vehicle Wiring And Bulb Configuration). The Assembly Replaces The Exterior Lens, Housing, And Bulb Holders Where Applicable, Restoring Light Output And Optical Directionality Required For Safe Nighttime Driving And Signalling.
Common Failure Modes
- Impact Damage: Cracked Or Broken Lens From Minor Collisions Or Parking Impacts.
- Water Ingress: Seal Failure Allowing Moisture To Enter, Causing Corrosion Of Contacts Or Condensation That Reduces Light Output.
- Mounting Tab Breakage: Plastic Tabs Fatigue Or Snap During Removal/Installation Or After Long-Term Use.
- Connector Or Socket Corrosion: Electrical Contacts May Corrode Leading To Intermittent Operation.
- UV Degradation: Lens Fading Or Clouding Over Time Reducing Visibility.
Replacement Guide
Recommended For Experienced Mechanics And Competent DIYers. Typical Replacement Steps:
- Open Rear Hatch/Access Panel And Remove Interior Trim Or Covering To Expose Lamp Fasteners.
- Unscrew The Retaining Bolts/Screws Securing The Lamp Assembly.
- Carefully Disconnect The Electrical Connector From The Lamp (Note Locking Tabs).
- Remove Old Lamp Assembly, Inspect Mounting Area And Replace Any Damaged Gaskets Or Seals.
- Fit New Lamp Assembly Into Position, Reattach Fasteners And Reconnect Electrical Connector.
- Test All Functions: Tail, Brake, Turn Signal And Reverse/Fog If Applicable. Ensure Correct Bulb Operation And Secure Mounting.
- Reinstall Interior Trim And Verify There Are No Rattles Or Misalignment.
Installation Recommendations
- Work In A Dry, Well-Lit Area To Prevent Contamination Or Moisture Trapping During Installation.
- Inspect And Replace Damaged Seals Or Gaskets To Prevent Future Water Ingress.
- Check Electrical Connector Pins For Corrosion; Clean Contacts If Necessary Before Reconnection.
- Do Not Overtighten Fasteners To Avoid Breaking Plastic Mounting Tabs; Tighten Evenly.
- After Installation, Verify That All Lighting Functions Operate Correctly From Inside The Vehicle And From Outside.
Why The Part Most Commonly Fails
Rear lamps on urban cars like the Peugeot 206 are most often damaged by minor impacts (parking knocks) and by degraded seals that allow moisture ingress. Moisture and dirt lead to corroded contacts and sockets or electrical faults. Plastic mounting tabs can also become brittle with age and break during removal or after repeated vibration, causing the lamp to sit loosely and be more vulnerable to damage.
Buying this complete right rear lamp assembly ensures a factory-aligned fit and restores full rear lighting performance, improving safety and compliance with road regulations. Ideal For Workshops And Skilled DIY Enthusiasts Replacing A Damaged Or Faulty Tail Lamp On Peugeot 206 Models Up To 06/2003.
