Description
Right passenger-side rearview mirror for Stellantis vehicles
Electrically adjustable and heated, electrically foldable toward the vehicle
Color EJG – NUIT BLUE PAINT
FXT – CORNELIE BLACK
Driver’s door
7 PIN
Part description
Used exterior rearview mirror marked 98169900XT, with electric adjustment, heating and electric folding toward the vehicle. A practical replacement if the mirror is damaged or its controls fail, provided it matches the original version. The information specifies a 7-pin connection and the color designations EJG – Nuit blue and FXT – Cornelie black.
Fitting-side notice: the product name specifies a left mirror, while the original description specifies a right passenger-side mirror and also mentions the driver’s door. The information is therefore contradictory on this point, and the side cannot be confirmed unambiguously. When selecting a replacement, compare the original part’s designation, shape, mounting and connector; the number of pins alone is not sufficient.
Technical information
- Manufacturer: not specified; the information includes the designation Stellantis CITROEN PEUGEOT.
- Model: Citroën Berlingo K9; FIAT DOBLO III; OPEL COMBO E K9; PEUGEOT RIFTER; Toyota ProAce City.
- Other numbers: not specified.
- Part type: exterior rearview mirror.
- Condition: used part.
- Functions: electric adjustment, heating and electric folding toward the vehicle.
- Connection: 7 PIN.
- Color designations: EJG – NUIT BLUE PAINT; FXT – CORNELIE BLACK.
- Fitting side: unclear due to contradictory information.
The model names are taken from the product labels. They do not, by themselves, establish suitability for every version of the vehicles listed; what matters is whether the specific mirror and its electrical equipment match.
Product codes
- Product codes: 98169900XT.
- Color code: EJG – NUIT BLUE PAINT.
- Additional color designation: FXT – CORNELIE BLACK.
When searching for a replacement mirror by number 98169900XT, also compare the side, base design, connector and available functions with the removed part.
Installation recommendations
The following general procedure applies to electrically adjustable and folding rearview mirrors. The precise access to the fasteners, trim removal and power disconnection procedure depend on the specific model and vehicle version. Follow the manufacturer’s service procedure.
1) Before installation
- First resolve the discrepancy in the side designation by comparing the physical design with the original mirror.
- Compare the product number, base, mounting points, sealing surface, wiring routing and connector shape, including the contact arrangement.
- Check the glass, housing, mounting, joint and wiring of the used part. Look for cracks, looseness, damaged insulation or corroded contacts.
- Verify that the original mirror has the corresponding electrical functions. Do not force the folding mechanism.
2) Tools and materials required
Suitable hand tools for the fasteners used, plastic trim removal tools, protection for painted surfaces and a soft cloth are usually sufficient. For any electrical measurements, use an appropriate measuring instrument and the wiring diagram for the specific vehicle.
3) Step-by-step installation
- Park the vehicle safely, switch off the ignition and secure it against being started unintentionally.
- Following the manufacturer’s instructions, allow the electrical systems to enter their idle state and disconnect the power as specified.
- Protect the surrounding painted surfaces and carefully remove only the covers or trim needed to access the mounting and connector.
- Note the original wiring route. Release the connector lock and disconnect it without pulling on the wires.
- Support the mirror and gradually release its fasteners so that it does not fall and damage the door.
- Remove the original part, clean the mounting surface and check the condition of the seal and the vehicle’s mounting points.
- Compare the two parts again. If the side, base or electrical connection does not match, do not continue with the installation.
- Position the replacement mirror without pinching the wiring or seal. Tighten the fasteners according to the manufacturer’s service procedure.
- Route the wiring along its original path, secure it and connect the connector so that its lock engages properly.
- Restore power according to the manufacturer’s instructions, check the functions and refit the removed covers and trim.
4) Post-installation checks and function verification
- Test the electric glass adjustment and folding and unfolding. Movement should be smooth, without sticking or unusual noises.
- Check the heating under the conditions in which the specific vehicle activates it.
- Check that the mirror is firmly mounted, the seal is seated and the trim is fitted correctly.
- Adjust the view before driving. During a short test drive, watch for image vibration or unusual aerodynamic noise; test folding while the vehicle is stationary.
5) Common installation mistakes and how to avoid them
- Wrong side or equipment: compare the physical design and electrical connection; do not rely on the product name alone.
- Pinched wiring: check its routing and ensure there is enough clearance before tightening.
- Damage to the mounting from overtightening: follow the manufacturer’s procedure and do not use excessive force.
- Incorrectly seated seal: clean the mounting surface and check that the seal sits evenly.
- Forcing the mirror to fold or connecting power incorrectly: operate the mechanism as intended and perform electrical tests only if you understand the wiring.
Reasons for part damage
General causes of damage to this type of rearview mirror include:
- Impacts while parking or passing obstacles, which can damage the housing, glass, joint or mounting.
- Forcing the mirror to fold or moving it against an obstacle or ice, which can overload the folding mechanism.
- Moisture and contact corrosion, which can interfere with electric adjustment or heating.
- Wear of moving parts over prolonged use.
- Damaged wires or incorrect previous installation, such as pinched wiring or inadequate sealing.
These causes are general and do not describe faults identified in the offered part.
